Controllers designed to control ventilation units with various types of heat recovery and other components, found in heat recovery devices.

Two choices of controllers:

ReguLar - the bigger options, with more inputs and outputs, for more complex devices.

ReguLite - the smaller, simpler option.

Both use the same firmware, called Ventwork. Slim design makes it easy to retrofit to manny devices, as well as develop around it.

The user interface panels are intuitive, easy to use for the end consumer, as well as easy to service and make commisioning with. Without any extra help, the user interfaces may be switched, as they share the same plug.

Possibility to also connect the controllers to your computer via USB cable, and make the setup as well as control the unit day-to-day easily.

Can be sold as full sets with all required sensors, or separated, if the client decides to mix & match between the controller and user interface.

Designed to use in ventilation systems as pre-heaters or re-heaters, together with ventilation units, or other ventilation components, such as CAV or VAV valves.

All standard sizes are available, as well as all control options that exist in the market. Wiring diagram or control type can be adjusted to better suit your needs and give an advantage compared to the competition, or to better interact with the ventilation device that it will be working in tandem with.

All of the heaters are equipped with automatic and manual safety thermostats, and every single one is checked before leaving the factory.

Possible choices of add-ons:

Airflow sensor;

Differential pressure switch;

Internal power contactor;

Alarm contacts;

ModBus communication.

Also a possibility to customize.

Customized electric heaters may be designed and manufactured, based on clients requirements on space, controls and power output.

We always take into account the surrounding material, where the unit will be used, how the heater is expected to perform and be controlled.

With the knowledge throughout the years, we help our customers with heating design and choices from the very first steps of ventilation unit design, to the final samples and production launch.

Water based duct heaters and coolers, designed to use in ventilation systems.

Coolers are insulated and equipped with drainage trays for condensation. Coolers may also be used as heaters.

Calculation tool available.

Controllers designed to control ventilation units with various types of heat recovery and other components, found in heat recovery devices.

Two choices of controllers:

ReguLar - the bigger options, with more inputs and outputs, for more complex devices.

ReguLite - the smaller, simpler option.

Both use the same firmware, called Ventwork. Slim design makes it easy to retrofit to manny devices, as well as develop around it.

The user interface panels are intuitive, easy to use for the end consumer, as well as easy to service and make commisioning with. Without any extra help, the user interfaces may be switched, as they share the same plug.

Possibility to also connect the controllers to your computer via USB cable, and make the setup as well as control the unit day-to-day easily.

Can be sold as full sets with all required sensors, or separated, if the client decides to mix & match between the controller and user interface.

Designed to use in ventilation systems as pre-heaters or re-heaters, together with ventilation units, or other ventilation components, such as CAV or VAV valves.

All standard sizes are available, as well as all control options that exist in the market. Wiring diagram or control type can be adjusted to better suit your needs and give an advantage compared to the competition, or to better interact with the ventilation device that it will be working in tandem with.

All of the heaters are equipped with automatic and manual safety thermostats, and every single one is checked before leaving the factory.

Possible choices of add-ons:

Airflow sensor;

Differential pressure switch;

Internal power contactor;

Alarm contacts;

ModBus communication.

Also a possibility to customize.

Customized electric heaters may be designed and manufactured, based on clients requirements on space, controls and power output.

We always take into account the surrounding material, where the unit will be used, how the heater is expected to perform and be controlled.

With the knowledge throughout the years, we help our customers with heating design and choices from the very first steps of ventilation unit design, to the final samples and production launch.