Detergent, deodorant, sanitizer, antibacterial, germicide pleasantly scented for air-conditioner filters, car filters. Product according to law 155 on H.A.C.C.P.

INSTRUCTIONS FOR USE: Before treating filters and finned packs with CLIMASAN, clean them with CLIMANET. Spray the product directly on the filters concerned almost once a week. The powerful action of CLIMASAN ensures the elimination of viruses, bacteria and pathogenic germs pleasantly scenting the room.

TECHNICAL DATA: pH: 7 ÷ 8 Mean action time: about 2 minutes Biocide activity: Escherichia coli, Proteus mirabilis, Pseudomonas aeruginosa, Staphylococcus aureus, Candida albicans, Saccharomyces cerevisiae, Legionella pneumophila. Bomb pressure: 3,5 bars Active principle: 10 %

Climanet spray is a low residue foaming product with bacteriostatic, degreasing and sanitizing action, specific for lamellar coils and finned packs of air conditioners and fan-coils, for indoors and outdoors. It dissolves dirt, even of an organic nature (e.g. midges), accumulated on the reed packs of air conditioners, compressors, radiators. Produced in accordance with Law 155/97 on H.A.C.C.P.

METHOD OF USE:
Dispense directly to interested parts periodically as needed. The foam that is produced has a
disintegrating action and removes bacteria from dirt and cannot be rinsed. In the internal units, the
condensation moisture will in fact exert a sufficiently washing and sanitizing action.

TECHNICAL DATA:
Appearance: amber liquid
Odor: characteristic
Relative density of the liquid phase: 1,002 ± 0,005 g/cm³
pH: 10,81 ± 0,5
Dry residue %: 2,3 ± 0,5
Can pressure @ 20 °C: 3,5 Bar
Container volume: 800 ml
Volume of the product: 600 ml
Boiling point: ~100 °C
Solubility in water: solubile
Flammability of the propellant: extremely flammable

Dissol Plus Chlor is a concentrated, intense action drain cleaner, suitable for both professional and domestic-private use, effective for freeing in a few minutes pipes clogged with organic deposits such as: hair, paper, food waste, grease residues, etc. Formulation based on concentrated caustic soda, sodium hypochlorite and biocides, as well as co-formulants that amplify the wetting/disintegrating power. It does not corrode or damage metal and synthetic pipes.
Fast-acting thanks to the complex and effective formula, it is able to free the drains in a few minutes, restoring the correct functioning of the pipes. Furthermore, the formulation of the product with active chlorine and biocides guarantees perfect sanitation of the pipes, eliminating any bacterial proliferation as well as bad odors.

APPLICATIONS:
Dissol Plus Chlor can be used in drains of toilets, sinks, sanitary ware, wells and septic tanks,
especially in professional or domestic / residential kitchens and bathrooms in communities such as
gyms, motorway bars, restaurants, bars.

HOW TO USE:
For sinks, showers, bidets, small pipes: slowly pour the recommended dose of product down the drain:
• Sinks: 1/5 of the bottle
• WC and drains in general: 1/3 of the bottle
Wait 15 - 20 minutes and run plenty of water, preferably hot.

ATTENTION: Pour slowly and do not stand near while the product works. Before use, make sure that no other chemicals of any nature have been introduced into the drain. In particular, never mix with acid-based clearing agents (eg DISSOL / DISGRETOR). Do not put in contact with aluminum,
galvanized sheet and magnesium alloys. Avoid contact with skin and use goggles and rubber gloves. The product in contact with water generates heat. In any case, consult the safety data sheet of the product.

PRECAUTIONS:
Prevent the product from reaching the ground, groundwater and waterways. Otherwise, notify the
competent authorities. Collect the liquid with absorbent material (sand, absorbent powders), clean the area with plenty of water. Dispose of the material according to local and national regulations.

Dark green putty paste Kolgas-Uni is a plastic sealant for threaded and unthreaded joints tight.
Kolgas-Uni always keeps soft, elastic and unchanged during the time preventing oxydation and
corrosion of threads. Use together with hemp or cloth, mineral fibres gaskets or rubber rings etc.
It has an anti-drying action on gaskets or rings, and an antiscuff action on threads.

COMPOSITION:
Mixture of petroleum greases with a high melting point and inert charges.

APPLICATIONS:
To be specifically used for gas tight, methane tight, steam tight, water tight, food liquids tight, etc. It is not suitable for use with LPG and OXYGEN.

TECHNICAL DATA:
Appearance: dark green paste
Odor: characteristic
Specific weight: 1,274 ± 0,010 g/cm³
Working temperature for hot water and steam: from -35 to +130 °C / 7 bars
Working temperature for gas: from -35 to +70 °C / 5 bars
Flash point: > 300 °C
Water solubility: none
Product: Non-toxic when inhaled or touched; without solvents

It is a unique concentrated product with 4 functions. It has a disintegrating action for sludge and slurries and also exerts a protective antiscale action in the presence of hard water, providing anticorrosive protection toward all constituent metals in systems, particularly aluminum and its alloys. It is also formulated with a powerful broad-spectrum biocide that can inhibit algal growth in low-temperature systems (e.g., radiant floors). The overall action is sanitizing and does not need to be flushed when used properly in conjunction with appropriate MAGNEX series magnetic defangment filter.

EFFECTIVENESS:
1. Restorative: breaks down and disperses any type of fouling present in thermal and refrigerant circuits, whether inorganic (rust, limestone, magnetite, machining residues, etc.) or organic (algae, biofilm, bacteria, etc.) in nature.
2. Antiscalant: the sequestering active ingredients in the formulation make it possible to keep calcium and magnesium salts dissolved in water in dispersion, thus preventing the precipitation of lime scale within the circuit as well as guaranteeing over time the correct heat exchange capacity of the system, preserving the system itself from possible occlusions and keeping consumption to a minimum.
3. Anticorrosive: the presence of a broad package of inhibitors formulated on the basis of azoles and molybdates allows the product to exert a prolonged anticorrosive action (even years after loading) toward all metals constituting the systems, particularly toward amphoteric metals such as aluminum and light alloys (aluminum-silicon).
4. Antibacterial: the broad-spectrum biocide present in the formulation, in addition to performing a preservative function of the product itself, makes it possible to preserve circuits running at low temperatures (30 ÷ 40 °C e.g., radiant floors, geothermal and refrigerants), from algal/bacterial proliferation resulting in algae stratification therefore cold areas in the house as well as higher energy consumption.

METHOD OF USE:
The product is recommended on medium-lived, even dated, but NOT compromised systems, in conjunction with a magnetic filter-deflector to be installed on the return to the boiler. Load directly from the filter, or via Disiflux sanitizing pump or an easy entry point of the system, at the rate of 0.5 %, i.e. 1 liter for every 200 liters of liquid circulating in the system. Periodic cleaning of the sludge-magnetic filter will be necessary and will depend on the amount of sludge in the circuit. Indicatively, a filter cleaning is recommended a few days after the product has been placed in the circuit, then 10 to 15 days apart, and then after more 30 gg repeating the operation for a few months. The amount of sequestered sludge as well as the turbidity of the water itself will tend to improve gradually after each inspection. Please consult Facot Chemicals Technical Department for more information and follow the requirements of UNI 8065:2019 for subsequent controls.

Corrosion proofing insulating bands for the protection of underground and aerial mains or pipes.
Paraffinic, dielectric with a polyethylene film on one side.

APPLICATIONS:
To be used whenever pipes have to be protected by corrosion due to atmospheric, chemical,
environmental agents. Suitable also for the protection from stray currents of metal surfaces, for the
outer binding of tanks, underground, aerial and underwater mains or pipes. The band represents an
excellent steam barrier and thanks to its chemical inertia it is a good protection from the above
mentioned agents, too.
Paratex band has a quite total application versatily since it can be used in those points impossible
to reach, as for example curves, valves etc.

COMPOSITION:
Synthetic fibre fabric, that can not be altered by soil chemical, bacteriologic and mycotic agents;
it is impregnated with a corrosion proofing paste based on paraffinic hydrocarbons specially
treated and charged.

CHARACTERISTICS:
Once it has been applied, it keeps its plasticity and inalterability. It is waterproof (saline water too),
gasproof and it can be used at a temperature ranging from -50 °C to +50 °C.

COMPATIBILITY OF MATERIALS:
Paratex tape, thanks to its composition based on paraffin hydrocarbons is chemically inert and
therefore compatible with all materials used in buildings of all types including metal and plastic
polymers like PE, PP, PES, PVC, ABS, PU.

INSTRUCTIONS FOR USE:
Wind up the band overlapping 10/15 mm two following turns, then wear a glove for cold levelling
off, to obtain an homogeneous and flat surface. On rusted or irregular surfaces it is recommended
an accurate cleaning with a hard brush.

Super concentrated descaling and sanitizing detergent for waste cisterns. Specific for the removal of limescale deposits, encrustations and blackening such as rust and stubborn dirt that form inside the toilet cisterns. Thoroughly whitens and sanitizes surfaces, eliminating unpleasant odors.

Ready-to-use antifreeze liquid added with fluorescent leak detector. Aligel HC30 Bio, as permanent PROPYLENE GLYCOL-BASED antifreeze, does not contain amines, nitrites, phosphates, silicates and borates in its inhibition pack. Contrary, it has a long-term organic inhibition and compared to the common antifreezes it has a very high (doubled) alkaline stock. Easily biodegradable. Protection of Aligel HC30 Bio is suitable for all metals, especially aluminum, his alloys and copper, that are usually the main parts of a cooling or heating system. Specific for food plants and solar panels, diluted with demineralised water as expressly required by the technical Norm UNI 8065:2019.Moreover, thanks to its formulation it is compatible with all materials constituting heating pumps.

INSTRUCTION FOR USE: Clean carefully the interested parts of the system according to the UNI 8065:2019 norm in force; if needed make a pickling of the pipes with Ferronex or ZInconex-LQ in order to eliminate slags or welding residues. Introduce ALIGEL HC30 BIO into the circuit from the more available point. Make the system run cold for some hours and after the boiler is on, vent carefully from the point where there is scarce circulation.

FREEZE PROTECTION / BOILING POINTS: Freezing point of ALIGEL HC30 BIO is -32 °C. Boiling point is +104 °C to atmospheric pressure, up to a value of +160 °C with pressure 5 bar.

BEHAVIOUR AGAINST RUBBER SLEEVES AND PLASTIC PARTS: ALIGEL HC30 BIO, thanks to first distillation PROPYLENE GLYCOL basis and to the choice of additives in its inhibition pack is a very reliable food product against non-metal products making up a heat exchange circuit.

ALIGEL HC30 BIO CONFORMS TO THE FOLLOWING NORMS: ASTM D 3306 – Type 2 (propylene-glycol based antifreeze).

Viscoelastic adhesive tape made of polyisobutylene-based butyl putty supported by high density
polyethylene films.

PECULIARITIES:
Great stretch capacity on both directions. Given the high adhesive, self-amalgamating power, it
does not need a fixing primer. It perfectly impermeabilizes surfaces, insulating them from soft
chemical and atmosferic agents.

APPLICATIONS:
Corrosion proofing covering for underground and overhead pipes (protected with aluminium),
sealing of metallic and cement surfaces in the building sector (joints, skylights, chimney flashings,
cold flues, conditioning channels, etc.). The great stretch capacity gives the tape a quite universal
adaptability to all surfaces, even to the most irregular ones (curves, Te, spigot joints, etc.). As for the
product application, the surface has only to be clean and not humid. It has to be stripped exerting
the necessary pulling stress according to the situation. In fact it can be stretched up to more than
700 % of its original length. The final thickness changes according to the pulling stress exerted. An
overlap of at least 10 % of the tape width is recommended.

Detergent, deodorant, sanitizer, antibacterial, germicide pleasantly scented for air-conditioner filters, car filters. Product according to law 155 on H.A.C.C.P.

INSTRUCTIONS FOR USE: Before treating filters and finned packs with CLIMASAN, clean them with CLIMANET. Spray the product directly on the filters concerned almost once a week. The powerful action of CLIMASAN ensures the elimination of viruses, bacteria and pathogenic germs pleasantly scenting the room.

TECHNICAL DATA: pH: 7 ÷ 8 Mean action time: about 2 minutes Biocide activity: Escherichia coli, Proteus mirabilis, Pseudomonas aeruginosa, Staphylococcus aureus, Candida albicans, Saccharomyces cerevisiae, Legionella pneumophila. Bomb pressure: 3,5 bars Active principle: 10 %

Climanet spray is a low residue foaming product with bacteriostatic, degreasing and sanitizing action, specific for lamellar coils and finned packs of air conditioners and fan-coils, for indoors and outdoors. It dissolves dirt, even of an organic nature (e.g. midges), accumulated on the reed packs of air conditioners, compressors, radiators. Produced in accordance with Law 155/97 on H.A.C.C.P.

METHOD OF USE:
Dispense directly to interested parts periodically as needed. The foam that is produced has a
disintegrating action and removes bacteria from dirt and cannot be rinsed. In the internal units, the
condensation moisture will in fact exert a sufficiently washing and sanitizing action.

TECHNICAL DATA:
Appearance: amber liquid
Odor: characteristic
Relative density of the liquid phase: 1,002 ± 0,005 g/cm³
pH: 10,81 ± 0,5
Dry residue %: 2,3 ± 0,5
Can pressure @ 20 °C: 3,5 Bar
Container volume: 800 ml
Volume of the product: 600 ml
Boiling point: ~100 °C
Solubility in water: solubile
Flammability of the propellant: extremely flammable

Dissol Plus Chlor is a concentrated, intense action drain cleaner, suitable for both professional and domestic-private use, effective for freeing in a few minutes pipes clogged with organic deposits such as: hair, paper, food waste, grease residues, etc. Formulation based on concentrated caustic soda, sodium hypochlorite and biocides, as well as co-formulants that amplify the wetting/disintegrating power. It does not corrode or damage metal and synthetic pipes.
Fast-acting thanks to the complex and effective formula, it is able to free the drains in a few minutes, restoring the correct functioning of the pipes. Furthermore, the formulation of the product with active chlorine and biocides guarantees perfect sanitation of the pipes, eliminating any bacterial proliferation as well as bad odors.

APPLICATIONS:
Dissol Plus Chlor can be used in drains of toilets, sinks, sanitary ware, wells and septic tanks,
especially in professional or domestic / residential kitchens and bathrooms in communities such as
gyms, motorway bars, restaurants, bars.

HOW TO USE:
For sinks, showers, bidets, small pipes: slowly pour the recommended dose of product down the drain:
• Sinks: 1/5 of the bottle
• WC and drains in general: 1/3 of the bottle
Wait 15 - 20 minutes and run plenty of water, preferably hot.

ATTENTION: Pour slowly and do not stand near while the product works. Before use, make sure that no other chemicals of any nature have been introduced into the drain. In particular, never mix with acid-based clearing agents (eg DISSOL / DISGRETOR). Do not put in contact with aluminum,
galvanized sheet and magnesium alloys. Avoid contact with skin and use goggles and rubber gloves. The product in contact with water generates heat. In any case, consult the safety data sheet of the product.

PRECAUTIONS:
Prevent the product from reaching the ground, groundwater and waterways. Otherwise, notify the
competent authorities. Collect the liquid with absorbent material (sand, absorbent powders), clean the area with plenty of water. Dispose of the material according to local and national regulations.